Product name	Exterior	Applicable material	Dry condition	Curing system	Curing temperature	Temperature resistance（℃）	Remarks
TC-SS-609PPA/B	Colorless transparent liquid	Metal, PBT, PI, glass	100℃-130℃	Platinum system vulcanization	100℃-130℃	-60℃-200℃	Sprayed or dipped on the surface of the substrate
TS-SS-609PPA-1/PPB-1	Colorless transparent liquid	Nylon, glass, some metals	100℃-130℃	Platinum system vulcanization	100℃-130℃	-60℃-200℃	Sprayed or dipped on the surface of the substrate
TC-SS-8020	Colorless transparent liquid	PET	80℃-100℃	Platinum system vulcanization	100℃-170℃	-60℃-200℃	Sprayed or dipped on the surface of the substrate
TC-SS-8020PT	Colorless transparent liquid	PET、PEN	80℃-100℃	Platinum system vulcanization	100℃-170℃	-60℃-200℃	Sprayed or dipped on the surface of the substrate
TC-SS-831PC	Colorless transparent liquid	PC	80℃-100℃	固态Platinum system vulcanization	100℃-130℃	-60℃-200℃	Sprayed or dipped on the surface of the substrate
TC-SS-831PCA/B	Colorless transparent liquid	PC	100℃-130℃	Liquid glue platinum system vulcanization	100℃-130℃	-60℃-200℃	Sprayed or dipped on the surface of the substrate
TC-SS-609SA/SB	Colorless transparent liquid	Nylon, glass	100℃-130℃	Platinum system vulcanization	100℃-130℃	-60℃-200℃	Sprayed or dipped on the surface of the substrate
TC-SS-609MH	Light yellow transparent liquid	Metal, PBT, epoxy, glass	80℃-120℃	Peroxide system vulcanization	160℃-180℃	-60℃-200℃	Sprayed or dipped on the surface of the substrate
TC-SS-931A/B	Colorless transparent liquid	PPSU, modified PC, metal, PI, PBT, glass, PET	100℃-130℃	Platinum system vulcanization	100℃-130℃	-60℃-200℃	Sprayed or dipped on the surface of the substrate
TC-SS-751A/B	Translucent liquid (high viscosity)	Nylon, glass fiber	150℃	Platinum system vulcanization	100℃-170℃	-60℃-200℃	Sprayed or dipped on the surface of the substrate
YET-B	Light yellow gelatinous	PET	150℃	Platinum system vulcanization	100℃-170℃	-60℃-200℃	Add to rubber

1. First use a non-corrosive solvent such as cyclohexane and n-heptane to remove the oil and dust on the surface of the substrate to be adhered, and then put it in an oven to dry at 100℃*10min, and take it out to cool.
2. Glue preparation ratio: (1 part of agent A: 1 part of agent B) Before using the glue, it needs to be added in proportion and mixed well before use.
3. ①Spraying: Spray glue evenly on the surface of the product. The thickness of the spraying film should be between 2-3μm. Then put it in the air for about 1min and put it in a 100℃ oven for 10min (when spraying, ensure that the spray gun is air sprayed. No water vapor is sprayed out); Bake in the box for 10 minutes.
    ②Soaking: soak the product in the glue for 10-20s and then take it out, dry the surface area of ​​the product and put it in a 100℃ oven for 10min;
    ③Coating: Use cotton or a brush to evenly coat the glue on the surface of the product (if there is liquid accumulation, it can be dried). The thickness of the coating film should be about 3-5μm, and then put it in an oven at 100°C for 10 minutes.
4. After baking, take out the adhesive-coated object and place it in a drying oven to cool to room temperature, and then attach the unvulcanized silicone rubber to it. Put it into the model and pressurize and heat vulcanize, the recommended molding temperature is 100-115℃ (if the temperature is too high, it may cause product deformation or produce bubbles to affect the bonding performance, etc.), the pressure is 70-130kgcm2 (after the silicone is fully vulcanized, it can be produced Mold), due to the high temperature when the mold is released, please wait until it has cooled to room temperature before testing the adhesion. Do not tear the material and silicone at high temperatures.

1. After the adhesive is used, the bottle cap should be tightly closed at any time to prevent solvent volatilization and moisture intrusion from affecting the quality.
2. The air humidity should be controlled below 50% during operation.
3. This product can not be mixed with organic compounds containing N, P, S, etc., or exposed to the air for a long time, deliquescence and dripping into water, so as not to affect the bonding effect.
4. After the glue is mixed, it is recommended that the 4H is used up, and the adhesive force of the glue will decrease if it exceeds 4H.
5. It is recommended that the product be used up within 16 hours after brushing the glue. The above information is for reference only, if you have any questions, please contact us

1. 1/KG can
2. The shelf life is 3 months. After the shelf life, it can still be used after passing the inspection.

1. This product should be stored in a cool place at 25°C away from light, avoid sunlight, so as to avoid product decomposition and avoid mixing with water. A slight precipitation may occur during storage, which is due to the nature of the resin and does not affect the adhesion.
2. This product contains organic solvents. It must be stored and transported in accordance with the flammable product rules. When using, pay attention to ventilation and prevent exposure to open flames.